30+ CNC machines. One roof.

5–9 axis machining capabilities running 24/5 — multi-axis mill-turn centers, twin-spindle turning, and automated cells sized for first article through full-rate production.

Built around the part

We buy machines for the work we take on, not the other way around. Complex geometries in difficult materials need the axes, the rigidity, and the single-setup accuracy to hold tolerance from the first part to the last one.

30+
CNC machines
in-house
5–9
Axis machining
capabilities
24/5
Production
capacity
0.0002"
Tolerances achieved
in production

Featured equipment

A representative look at the multi-axis platforms doing the hardest work on our floor. Every one of them is set up to take a part from raw stock to finished geometry in as few setups as possible.

DMG Mori DMC 125 FD 5-axis machining center with integrated turning
01 DMG Mori

DMC 125 FD

5-Axis Machining Center with Integrated Turning

Our largest 5-axis platform, with turning built into the same envelope. Large, complex housings and structural hardware get milled and turned without ever leaving the table — which is where tolerance stack-up usually comes from.

DMG Mori DMC 85 FD 5-axis machining center with integrated turning
02 DMG Mori

DMC 85 FD

5-Axis Machining Center with Integrated Turning

The same mill-and-turn approach in a tighter, stiffer envelope. Sized for mid-size parts where surface finish and feature-to-feature accuracy matter as much as the overall dimension.

DMG Mori monoBLOCK 65 5-axis machining center
03 DMG Mori

monoBLOCK 65

5-Axis Machining Center

A compact, rigid 5-axis workhorse. Simultaneous 5-axis contouring on smaller, feature-dense parts — brackets, manifolds, and fittings that would otherwise take four or five separate setups.

DMG Mori NTX 2000 9-axis mill-turn machining center
04 DMG Mori

NTX 2000

9-Axis Mill-Turn Machining Center

Nine axes of simultaneous turning and milling. The part goes in as bar or billet and comes out complete — turned, milled, drilled, and threaded in one continuous cycle with no re-fixturing.

DMG Mori NTX 3000 9-axis mill-turn machining center
05 DMG Mori

NTX 3000

9-Axis Mill-Turn Machining Center

The same done-in-one philosophy with the length to handle longer shafts and slender components — the parts where chatter and deflection usually decide whether the tolerance holds.

DMG Mori NZX 1500 multi-axis turning center with twin spindles and dual turrets
06 DMG Mori

NZX 1500

Multi-Axis Turning Center · Twin-Spindle, Dual Turrets

Two spindles and two turrets working the same part at once. Built for production turning at rate — the second spindle picks up the back side while the first is still cutting, which is how we hold cost down on higher-volume work.

Equipment list

Our machining platforms by category. Capacities and configurations vary across the floor — tell us about your part and we will tell you exactly which cell it runs in.

5-Axis Machining Centers
01
DMC 125 FDDMG Mori
5-axis machining center with integrated turning. Our largest 5-axis envelope.
02
DMC 85 FDDMG Mori
5-axis machining center with integrated turning, mid-size envelope.
03
monoBLOCK 65DMG Mori
Compact 5-axis machining center for feature-dense parts.
Mill-Turn Machining Centers
04
NTX 2000DMG Mori
9-axis mill-turn machining center. Turning and milling in a single continuous cycle.
05
NTX 3000DMG Mori
9-axis mill-turn machining center with extended length capacity.
Turning Centers
06
NZX 1500DMG Mori
Multi-axis turning center with twin spindles and dual turrets, built for production rate.

This list is a representative sample of our 30+ machine floor. For a complete equipment schedule against a specific program or part family, contact us and we will send it over.

Request a Quote

More than metal cutting

A machine is only as good as the process around it. Programming, fixturing, inspection, and traceability are what turn capacity into conforming parts, run after run.

Inspection

Advanced CMM inspection with digital quality planning and complete traceability from first article through production.

Automation

Automated cells and pallet systems that keep spindles cutting across unattended shifts, running 24/5.

Programming

In-house CAM programming and simulation, so complex multi-axis toolpaths are proven before a spindle ever turns.

Quality System

AS9100 and ISO 9001 certified, ITAR registered. Documented process control behind every part that leaves the building.

Quality & Certifications

Have a part that needs this kind of machine?

Send us the model and the print. We will tell you which cell it runs in, what it takes to hold your tolerance, and when we can deliver.

Request a Quote